How do I configure my 4 monitors in the PCoIP Zero Client OSD?
To configure 4 monitors to your preference, follow the steps below.  Before you begin, make sure that you know what monitor is connected to what PCoIP Zero Client port number. From the onscreen display (OSD) of your PCoIP Zero Client, browse to Options > …
Knowledge Base Article Tutorial Display Setup Zero Clients
Last modified: September 3, 2023
1714
Give it 1/5
Give it 2/5
Give it 3/5
Give it 4/5
Give it 5/5
Do PCoIP Zero Clients support single and multi-touch monitors?
Answer: PCoIP Zero Clients support selected ELO touch monitors in pre-session (using the Teradici OSD) since Firmware 3.4.0,and should support other touchscreen monitors (single and multi-touch) while in a PCoIP session. To make a connection using a …
Knowledge Base Article Advisory Display Zero Clients
Last modified: September 21, 2023
1708
Give it 1/5
Give it 2/5
Give it 3/5
Give it 4/5
Give it 5/5
Troubleshooting artifacts in a PCoIP Session
Problem During a PCoIP Session artifacts are appearing on the screen. The artifacts may stay or slowly disappear.   Cause and Resolution There are may reasons artifacts may appear on the screen. Some may be source issues such as the application or …
Knowledge Base Article Troubleshooting Performance Display HP Anyware Remote Workstation Card Zero Clients
Last modified: September 3, 2023
1703
Give it 1/5
Give it 2/5
Give it 3/5
Give it 4/5
Give it 5/5
Why is the BIOS not visible when my Dell workstation boots with a PCoIP Remote Workstation Card?
Scenario The BIOS on a Dell R5500/R5400 is not visible on boot up. After the OS loads, the monitor then displays the desktop. On some graphic cards, only the primary port is active during the POST phase of the host PC boot process. For example, when using …
Knowledge Base Article Troubleshooting Setup Display Remote Workstation Card
Last modified: September 3, 2023
1704
Give it 1/5
Give it 2/5
Give it 3/5
Give it 4/5
Give it 5/5
Getting blank screen or "source signal on other port" when connecting from zero client to VMware Horizon
Scenario: When using a PCoIP zero client connecting to VMware VM running Horizon Agent 8.2 if the VMware remote console is open while user is in session the zero client will display a blank screen or you may receive a message "source signal on other …
Knowledge Base Article Troubleshooting Display Third Party Enhancements Zero Clients
Last modified: September 3, 2023
1519
Give it 1/5
Give it 2/5
Give it 3/5
Give it 4/5
Give it 5/5
Client Display Health Check - Diagnostics and troubleshooting guide
Summary To receive a detailed client diagnostic report, create a client  support/log file bundle  and then submit this bundle to the PCoIP  health check   tool.  Once the files are submitted, it will take 5-10 minutes to produce a detailed report.  The …
Knowledge Base Article Diagnostics Display HP Anyware
Last modified: September 3, 2023
1450
Give it 1/5
Give it 2/5
Give it 3/5
Give it 4/5
Give it 5/5
Why is the BIOS not accessible from my PCoIP Workstation solution?
The BIOS must be able to enumerate the PCIe PCoIP Remote Workstation Card and support OHCI which typically does not occur until post BIOS. USB peripherals (keyboard, mouse etc.) connected to PCIe PCoIP Remote Workstation Cards as in a PCoIP Workstation …
Knowledge Base Article Advisory Display Remote Workstation Card
Last modified: September 14, 2023
1445
Give it 1/5
Give it 2/5
Give it 3/5
Give it 4/5
Give it 5/5
Mirroring displays on PCoIP Zero Clients
Requirements Tera2 dual port client (TERA2321) Firmware 4.1 or newer   Instructions From the PCoIP Zero Client's onscreen display (OSD) or both versions of the Management Console OSD - browse to Options > Configuration > Display > Enable Display Cloning …
Knowledge Base Article Tutorial Display Zero Clients
Last modified: November 7, 2022
1413
Give it 1/5
Give it 2/5
Give it 3/5
Give it 4/5
Give it 5/5
Why does HP Anyware specify a Nvidia and AMD driver for use with the PCoIP Graphics Agent?
HP Anyware performs extensive testing of the PCoIP Graphics Agent for Windows and the PCoIP Graphics Agent for Linux before release. As part of the tests, HP Anyware uses the latest Nvidia and AMD drivers available at the time. Upon release of the PCoIP …
Knowledge Base Article Advisory Display HP Anyware
Last modified: September 27, 2023
1239
Give it 1/5
Give it 2/5
Give it 3/5
Give it 4/5
Give it 5/5