Should I use an initial image quality of Q100?
An initial image quality of Q100 will deliver the highest quality of image PCoIP can deliver. Q100 is not lossless, for a lossless image, build to lossless must be enabled.  How to configure the Turn off Build-to-Lossless feature session variable in GPO …
Knowledge Base Article Advisory Display Performance Remote Workstation Card Zero Clients HP Anyware
Last modified: August 1, 2023
695
Encryption and bandwidth metrics used for various setups PCoIP Devices and VMware Horizon View
Answer:   Encryption and Bandwidth Metrics   Tera1 Zero Client Tera2 Zero Client Windows View Client Host Card No View Security Server Up to 220 Mbps AES-128 (not encapsulated) Up to 500 Mbps AES-128/AES-256| (not encapsulated/encapsulated) FW 4.1.0 and …
Knowledge Base Article Advisory Performance Third Party Enhancements Remote Workstation Card Zero Clients
Last modified: September 3, 2023
692
PCoIP Host Driver Software 4.3.1 does not automatically map the PCoIP remote workstation cards in Leostream.
Answer : If you try to automatically map the PCoIP remote workstation card (host card) running PCoIP Host Driver Software 4.3.1 and using the Leostream broker it will fail. If you downgrade the PCoIP Host Driver Software to 4.2.2 it automatically maps. …
Knowledge Base Article Troubleshooting Third Party Enhancements Remote Workstation Card
Last modified: September 14, 2023
658
What does "IPC: Frame encode took xxx ms so far. Dropping down the quality to index x." in the log files indicate?
Answer: In this case, the imaging encoder has determined that too many bits were being sent in the upper portion of the frame (i.e. flooding) which causes the frame to take longer to encode, and therefore appears unresponsive to the user (> 750 ms to …
Knowledge Base Article Troubleshooting Performance HP Anyware Zero Clients Remote Workstation Card
Last modified: December 9, 2022
649
Can I use an Ethernet hub or half-duplex network connection with a PCoIP Zero Client or PCoIP Remote Workstation Card?
No. PCoIP technology requires a full-duplex Ethernet connection from end to end. In modern networks, half-duplex links can still exist when using technologies such as Wi-Fi or point to point Wi-Fi or Microwave links. Older communication equipment in wired …
Knowledge Base Article Troubleshooting Performance Remote Workstation Card Zero Clients
Last modified: March 26, 2021
634
Why can't I get 2560x1600 Resolution on my PCoIP Remote Workstation Access Card (Host Card)?
Answer: Due to display changes after PCoIP Remote Workstation Card Firmware 4.2, you need to disable monitor emulation on all nonactive ports on the PCoIP Remote Workstation Card. Note: Dual port PCoIP Remote Workstation Cards support a maximum of one …
Knowledge Base Article Troubleshooting Display Remote Workstation Card
Last modified: November 18, 2022
633
Why does my PCoIP Remote Workstation hibernate or sleep and not power off remotely from my Tera 2 PCoIP Zero Client?
When a PCoIP Zero Client attempts to power down a Windows 7 or Windows 10 workstation host during a PCoIP session, the workstation may enter the sleep state rather than being shutdown. This will occur if Windows is configured to map the PC power button to …
Knowledge Base Article Advisory Session Remote Workstation Card Zero Clients
Last modified: July 3, 2020
633
PCoIP TROUBLESHOOTING STEPS: IEEE 802.1x Network Authentication
This article provides a brief list of troubleshooting steps for common issues with 802.1x authentication. It is not intended to be a comprehensive troubleshooting guide. These include scenarios for: Problems uploading IEEE 802.1x certificates to PCoIP …
Knowledge Base Article Troubleshooting Security Remote Workstation Card Zero Clients
Last modified: September 7, 2023
627