Troubleshooting a minidump (.dmp) file
When a HP Anyware software product experiences an issue and exits unexpectedly, a "miniDump" (.dmp) file is created. The file contains information as to the state of the application when it exits unexpectedly. MiniDump files have an associated log file, …
Knowledge Base Article Troubleshooting HP Anyware
Last modified: September 14, 2023
310
The incorrect workstation powers on when trying to connect to a PCoIP Remote Workstation Card from a PCoIP Zero Client
Problem You might encounter the following problem if you use a PCoIP Zero Client to switch between workstations, i.e. computers with a PCoIP Remote Workstation Card (host card) installed: the first workstation wakes up and connects normally, but the …
Knowledge Base Article Troubleshooting Remote Workstation Card Zero Clients
Last modified: September 19, 2023
312
PCoIP Zero Clients Energy Star Compliance
E-Star ENERGY STAR Certification of PCoIP Zero Clients Tera2 PCoIP zero clients may be certified for ENERGY STAR? rating under the E-Star 5.2 Program Requirements for Computers. Please check with your OEM Partner if they have applied for certification of …
Knowledge Base Article Advisory Zero Clients
Last modified: September 19, 2023
313
How does PCoIP share bandwidth over the network?
The BW Limit is dynamically calculated and represents the bandwidth the PCoIP session estimates to be available given the network conditions. The calculation takes into account the existing bandwidth usage, packet loss and any high latency spikes. The …
Knowledge Base Article Advisory Performance HP Anyware Remote Workstation Card Zero Clients
Last modified: December 9, 2022
308
What does "MCU not initialized" log message mean?
Problem You are unable to manage a zero client using the HP Anyware PCoIP Management Console 1.x (MC). The event logs reveal the following MCU errors: LVL:1 RC:-500        MCU :(tera_mcu_read_eeprom_bit): Cannot read from EEPROM, MCU not initialized. …
Knowledge Base Article Troubleshooting Management Remote Workstation Card Zero Clients
Last modified: September 19, 2023
305
How can I tell if the 802.1x certificate uploaded successfully?
A good test is to use the web UI to upload the 802.1x certificate. From the web UI, go to Upload> Certificate and view the screen. If the certificate is listed after a restart of the PCoIP Zero Client then the certificate was uploaded successfully (see …
Knowledge Base Article Tutorial Security Remote Workstation Card Zero Clients
Last modified: August 23, 2018
306
No warning message when VMware View Connection Server Certificate Check Mode is set to Warn if Connection may be insecure (Default)
This is expected behavior. Configured non-interactive session modes do not display VCS Warning messages in Warn if the connection may be insecure (Default) security mode.  Interactive session modes will display VCS Error messages in Warn if the connection …
Knowledge Base Article Troubleshooting Security Third Party Enhancements Zero Clients
Last modified: September 3, 2023
307
In VMware Horizon View, what does it mean when a particular USB issue happens on both the VMware View client and the PCoIP Zero Client?
Answer: If a USB peripheral has the same issue on both PCoIP Zero Clients and VMware View clients (repurposed PC, notebook or thin client running the View Client), it's likely that the issue is in the VMware virtual USB hub driver, or is an issue with …
Knowledge Base Article Troubleshooting Peripheral Devices Third Party Enhancements Zero Clients
Last modified: September 3, 2023
301
How do I change the FQDN (Fully Qualified Domain Name) of a PCoIP Zero Client?
First, change the PCoIP name to a new name. Currently, the "PCoIP Device Name" can only be changed on an individual basis in two locations: The  "OSD--> Configuration--> Label"  tab The  "AWI--> Configuration--> Label"  tab The default format is  …
Knowledge Base Article Advisory Management Management Console Zero Clients
Last modified: September 3, 2023
302