Why am I seeing high bandwidth from the PCoIP Zero Client for audio even though I am not recording anything?
Problem As soon as an audio application starts and samples data from the audio input, PCoIP traffic from the client to host increases significantly and is steady.   Cause Once an application requests audio from the line in or microphone inputs, the PCoIP …
Knowledge Base Article Troubleshooting Performance Zero Clients
Last modified: April 27, 2023
357
When using Management Console 3.0.0 I am not able to manage zero clients?
Impacts:   PCoIP Management Console 3.0.0 Scenario: When migrating from Management Console 2.x to Management Console 3.0.0 many zero clients fail to connect to the management console. If the management console is power cycled the zero clients are now able …
Knowledge Base Article Troubleshooting Management Console
Last modified: September 19, 2023
359
Profile application to Remote Workstation Card fails
Scenario : The remote workstation card is at a factory default. You set a basic Profile in the management console and apply the Profile. The Profile application fails. If you check the management console, there is no clue as to why the Profile failed. If …
Knowledge Base Article Troubleshooting Management Management Console Remote Workstation Card
Last modified: September 19, 2023
357
The incorrect workstation powers on when trying to connect to a PCoIP Remote Workstation Card from a PCoIP Zero Client
Problem You might encounter the following problem if you use a PCoIP Zero Client to switch between workstations, i.e. computers with a PCoIP Remote Workstation Card (host card) installed: the first workstation wakes up and connects normally, but the …
Knowledge Base Article Troubleshooting Remote Workstation Card Zero Clients
Last modified: September 19, 2023
346
Cannot import profile from Management Console 1.x into the PCoIP Management Console 2.x or 3.x
Answer : Importing Profiles from MC 1.x into MC 2.x is supported and documented in the user guide. Refer to the Administrators' guide for the release of the PCoIP Management Console in use. There have been a couple reports of users experiencing an issue …
Knowledge Base Article Troubleshooting Management Management Console
Last modified: September 19, 2023
346
Why do I get poor performance on an MPLS network?
There are a number of configuration requirements for using PCoIP protocol on an MPLS network.  Prioritize PCoIP packets as a best practice Avoid packet loss Avoid out-of-order packets PCoIP protocol may consider out-of-order packets as lost if the data …
Knowledge Base Article Troubleshooting Performance HP Anyware Remote Workstation Card Zero Clients
Last modified: December 9, 2022
340
Why doesn't the PCoIP Remote Workstation Card power up when it is installed to a particular PCIe slot?
This may be due to the restrictions of your host PC's motherboard that requires you to install graphics cards or other PCIe cards into certain PCIe slots. If a PCIe card is installed into an inappropriate PCIe slot, the host PC may stop loading any …
Knowledge Base Article Troubleshooting Setup Remote Workstation Card
Last modified: November 22, 2022
340
Does the Phillips Digital Pocket Memo work with a PCoIP Zero Client and VMware Horizon View?
Scenario A Philips Digital Pocket Memo (DPM) device does not operate after connecting to a PCoIP Zero Client using the USB EHCI controller (USB 2.0). Occasionally the PCoIP Zero Client unexpectedly restarts.   Cause The Philips Digital Pocket Memo device …
Knowledge Base Article Troubleshooting Peripheral Devices Zero Clients
Last modified: October 31, 2022
337
What does "MCU not initialized" log message mean?
Problem You are unable to manage a zero client using the HP Anyware PCoIP Management Console 1.x (MC). The event logs reveal the following MCU errors: LVL:1 RC:-500        MCU :(tera_mcu_read_eeprom_bit): Cannot read from EEPROM, MCU not initialized. …
Knowledge Base Article Troubleshooting Management Remote Workstation Card Zero Clients
Last modified: September 19, 2023
330